) Double-click Install Adobe Acrobat Reader DC to start the installation. When asked if you are sure that you want to open the file, click Open.Amcrest free download - Amcrest Connect, Amcrest Cloud, Amcrest Skyview, and many more programs. The Amcrest WiFi Smart Plug turns your iPhone.Edit config.json manually to add your cameras. Install this plugin using: sudo npm install -g homebridge-camera-ffmpeg -unsafe-perm. It is highly recommended that you use either Homebridge Config UI X or the HOOBS UI to install and configure this plugin. Please send an email to supportamcrest.com , salesamcrest.com or call 1-88.This plugin is supported under both Homebridge and HOOBS.
name: (Required) Set the camera name for display in the Home app. platform: (Required) Must always be set to Camera-ffmpeg. Manual Configuration Most Important Parameters You may want to check that to see if anyone else has gotten your model of camera working already, or share a configuration setup that works for you. Download fifa 2003 for androiddoorbell: Exposes the doorbell device for this camera. This can be triggered with dummy switches, MQTT messages, or via HTTP, depending on what features are enabled in the config. motion: Exposes the motion sensor for this camera. If not set, the plugin will grab one frame from source. stillImageSource: If your camera also provides a URL for a still image, that can be defined here with the same syntax as source. The most basic form is -i followed by your camera's URL. motionTimeout: The number of seconds after triggering to reset the motion sensor. See the project site for more detailed instructions. When enabled there will be an additional switch that triggers the motion or doorbell event. switches: Enables dummy switches to trigger motion and/or doorbell, if either of those are enabled. Amcrest Plugin Serial Number For DisplayfirmwareRevision: Set the firmware revision for display in the Home app. serialNumber: Set the serial number for display in the Home app. model: Set the model for display in the Home app. manufacturer: Set the manufacturer name for display in the Home app. This allows for motion alerts to appear on Apple TVs. motionDoorbell: Rings the doorbell when motion is activated. maxStreams: The maximum number of streams that will be allowed at once to this camera. This feature is still in development and a configuration that works today may not work in the future. returnAudioTarget: (EXPERIMENTAL - WIP) The FFmpeg output command for directing audio back to a two-way capable camera. (Default: false)Config Example with Manufacturer and Model Set If unbridged, the camera will need to be added to HomeKit manually. unbridge: Bridged cameras can cause slowdowns of the entire Homebridge instance. maxHeight: The maximum height used for video streamed to HomeKit. If not set, will use any size HomeKit requests. If set to 0, the resolution of the source is used. If not set, will use any frame rate HomeKit requests. If set to 0, the framerate of the source is used. maxFPS: The maximum frame rate used for video streamed to HomeKit. If not set, will use any size HomeKit requests. vcodec: Set the codec used for encoding video sent to HomeKit, must be H.264-based. forceMax: If set, the settings requested by HomeKit will be overridden with any 'maximum' values defined in this config. If not set, will use any bitrate HomeKit requests. (Default: FFmpeg automatically selects a video stream) mapvideo: Selects the stream used for video. packetSize: If audio or video is choppy try a smaller value, should be set to a multiple of 188. audio: Enables audio streaming from camera. encoderOptions: Options to be passed to the video encoder. If 'none' is included, the default video filters are disabled. videoFilter: Comma-delimited list of additional video filters for FFmpeg to run on the video. (Default: FFmpeg automatically selects an audio stream) Will use the name of the camera if blank. motionMessage: The message to watch for to trigger motion alerts. motionTopic: The MQTT topic to watch for motion alerts. (Default: false)"source ": "-i rtsp://myfancy_rtsp_stream ","additionalCommandline ": "-x264-params intra-refresh=1:bframes=0 ", debugReturn: Includes debugging output from the FFmpeg used for return audio in the Homebridge log. debug: Includes debugging output from the main FFmpeg process in the Homebridge log. tlsmqtt: Use TLS to connect to the MQTT broker. portmqtt: The port of the MQTT broker. See the project site for more information on using MQTT. If not set, HTTP support is not started. porthttp: The port to listen on for HTTP-based automation. If not set, no authentication is used. passmqtt: The password used to connect to your MQTT broker. If not set, no authentication is used. Useful if using helper plugins that translate to HTTP. localhttp: Only allow HTTP calls from localhost.
0 Comments
Leave a Reply. |
AuthorPrasanna ArchivesCategories |